Sensoray 2600 Manual de usuario Pagina 33
- Pagina / 80
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
2600 Family Instruction Manual
28
Chapter 5 : Common IOM Actions
Notes Most IOMs have provision for installing address
shunts. These shunts enable the system
integrator to specify an address for the module,
with a value in the range 0 to 15 decimal.
The MM does not use the board address; it is
provided for exclusive use by the Ethernet client.
For example, the client may use the module
address to differentiate between IOMs of the
same type, or to verify that IOMs are connected
to the correct IOM ports on the MM.
5.2.8 LinkQuery
Function Queries an IOM port to determine if a module is
present.
Opcode 0xFE
Command none
Response none
Notes In normal operation, LinkQuery should never
be invoked by the client. LinkQuery is
invoked by the gateway, in a manner that is
transparent to the Ethernet client, to determine if
a module is connected to a specific IOM port.
LinkQuery does not cause the target module’s
RCV or XMT indicators to light as this action is
not intended for use by the Ethernet client.
5.2.9 NOP
Function No operation.
Opcode 0xFF
Command none
Response none
Notes NOP may be used to acquire IOM status when no
other actions are required.
- Model 2600 Family 1
- Instruction Manual 1
- Table of Contents 2
- Chapter 1: Introduction 6
- 1.2 Network Protocols 7
- 1.3 Module Network Topology 8
- Chapter 2: System Wiring 9
- 2.3 System Wiring Example 10
- Chapter 2 : System Wiring 11
- Chapter 3: IOM Gateway 12
- 3.2 Action Lists 13
- 3.3 Module Commands (MCmd) 13
- 3.4 Module Responses (MRsp) 14
- 3.5 Format Translation 15
- 3.6 Packet Routing 16
- 3.7 Link Detection 16
- 3.7.4 IOM Port States 17
- 3.8 Error Detection 18
- 3.9 Gateway Actions 19
- 3.9.2 GetInterlocks 20
- 3.9.3 SoftReset 20
- 3.9.4 HardReset 20
- 3.9.5 ResetFlags 20
- 3.10 Specifications 21
- 4.1 Overview 22
- 4.2 Hardware Configuration 22
- 4.2.2 Device Networks 24
- 4.3 Com Port Packets 25
- 4.4 Com Port Commands 26
- 4.4.1.3 LED Behavior 27
- 4.4.2 Send 28
- 4.4.3 Receive 28
- 4.4.4 ClearFlags 28
- 4.4.5 Open 28
- 4.5 Specifications 30
- 5.1 Overview 31
- 5.2 Actions 31
- 5.2.8 LinkQuery 33
- 5.2.9 NOP 33
- 6.1 Introduction 34
- 6.2 Analog Outputs 34
- 6.3 Analog Inputs 34
- 6.4 Hardware Configuration 35
- 6.4.2 Analog Inputs 36
- 6.5 Reset 37
- 6.6 Actions 37
- 6.6.3 SetInputRanges 38
- 6.6.4 GetInputRanges 38
- 6.6.5 GetSnapshots 38
- 6.6.6 GetIntegrateds 39
- 6.6.7 GetInternals 39
- 6.6.8 SetLineFreq 39
- 6.7 Specifications 40
- 7.1 Introduction 41
- 7.2 Hardware Configuration 41
- 7.2.4 I/O Connectors 42
- 7.3 Channel Operating Modes 43
- 7.4 Reset 44
- 7.5 Status Flags 44
- 7.6 Actions 44
- 7.6.2 GetModes 45
- 7.6.3 SetPwmRatio 45
- 7.6.4 GetPwmRatio 45
- 7.6.5 GetInputs 46
- 7.6.6 GetOutputs 46
- 7.6.7 SetOutputs 46
- 7.7 Specifications 47
- 8.1 Introduction 48
- 8.2 Conversion Modes 48
- 8.3 Excitation 49
- 8.4 Analog Inputs 49
- 8.5 Hardware Configuration 49
- 8.5.2 Remote Sense Shunts 50
- 8.6 Reset 51
- 8.7 Actions 51
- 8.7.3 SetVoltages 52
- 8.7.4 ReadEeprom 52
- 8.7.5 WriteEeprom 52
- 8.8 Specifications 53
- 9.1 Introduction 55
- 9.2 Hardware Configuration 55
- 9.3 Reset 56
- 9.4 Actions 56
- 9.4.1 SetMode 57
- 9.4.2 SetCommonControl 58
- 9.4.3 SoftTrigger 58
- 9.5 Applications 60
- 9.5.3 PWM Generator 61
- 9.5.5 Period Measurement 61
- 9.5.6 Frequency Measurement 61
- 9.6 Specifications 62
- 10.1 Introduction 63
- 10.2 Hardware Configuration 63
- 10.2.4 I/O Connectors 64
- 10.2.5 Reserved Connectors 64
- 10.3 Reset 65
- 10.4 Status Flags 65
- 10.5 Actions 65
- 10.6 Specifications 66
- 11.1 Introduction 67
- 11.2 Hardware Configuration 67
- 11.2.4 I/O Connectors 68
- 11.3 Channel Operating Modes 69
- 11.4 Reset 69
- 11.5 Status Flags 70
- 11.6 Actions 70
- 11.6.3 SetOutputs 71
- 11.6.4 SetModes 71
- 11.6.5 GetModes 71
- 11.6.6 SetPwmRatio 71
- 11.7 Specifications 72
- 12.1 Introduction 74
- 12.2 Hardware Configuration 74
- 12.2.4 I/O Connectors 75
- 12.3 Channel Operating Modes 76
- 12.4 Reset 77
- 12.5 Status Flags 77
- 12.6 Actions 77
- 12.6.3 SetOutputs 78
- 12.6.4 SetModes 78
- 12.6.5 GetModes 78
- 12.6.6 SetPwmRatio 79
- 12.6.7 GetPwmRatio 79
- 12.7 Specifications 80
Relacionado con productos y manuales para Hardware Sensoray 2600
Hardware Sensoray 2410 API Manual de usuario
(39 paginas)
(39 paginas)
Hardware Sensoray 118 Manual de usuario
(38 paginas)
(38 paginas)
Hardware Sensoray 7429 Manual de usuario
(48 paginas)
(48 paginas)
Hardware Sensoray 421 Manual de usuario
(27 paginas)
(27 paginas)
Hardware Sensoray 425 Manual de usuario
(34 paginas)
(34 paginas)
Hardware Sensoray 417 Manual de usuario
(37 paginas)
(37 paginas)
Hardware Sensoray 627 Manual de usuario
(6 paginas)
(6 paginas)
Hardware Sensoray 623 Manual de usuario
(6 paginas)
(6 paginas)
Hardware Sensoray 327 Manual de usuario
(5 paginas)
(5 paginas)
Hardware Sensoray 328 Manual de usuario
(5 paginas)
(5 paginas)
Hardware Sensoray 422 Manual de usuario
(1 paginas)
(1 paginas)
Hardware Sensoray 626 Manual de usuario
(32 paginas)
(32 paginas)
Hardware Sensoray 2518 Manual de usuario
(30 paginas)
(30 paginas)
Hardware Sensoray 335 Manual de usuario
(12 paginas)
(12 paginas)
Hardware Sensoray 720RB Manual de usuario
(14 paginas)
(14 paginas)
Hardware Sensoray 7409TC Manual de usuario
(3 paginas)
(3 paginas)
Hardware Sensoray 512 DOS Manual de usuario
(24 paginas)
(24 paginas)
Hardware Sensoray 512 Manual de usuario
(18 paginas)
(18 paginas)
Hardware Sensoray 512 QNX Manual de usuario
(16 paginas)
(16 paginas)
Hardware Sensoray 2246 Manual de usuario
(50 paginas)
(50 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales